One can hardly imagine a world without electrical motors. They make air conditioners possible, they circulate the water in a swimming pool and they power vacuum cleaners. The list of uses for these devices are endless. Most people will be surprised if they take the trouble to count the number they have in and around their homes. They can be expensive to replace or repair, however. Luckily, DIY enthusiasts in Phoenix can consider electric motor rewinding themselves.
It is important to note that his type of project requires a high level of concentration and meticulous attention to detail. The device will not work if even small mistakes are made or if the rewind job was done poorly. If there are the slightest doubt it may be better to have the task performed by professionals. There is such a large variety of devices on the market that care should be taken when following on line instructions.
First, it is necessary to remove the housing in order to expose the armature, stator and windings. Experienced professional advise that detailed photographs be taken at this stage. When winding, the exact patterns and connections will have to be recreated and the photographs can be a big help in this regard. Even small mistakes can render the project a failure.
The next step is to take the wire from the brush pads, taking care not to disturb the tabs more than strictly necessary. The wire must be completely removed. Thereafter the coils can be cut in order to free them from the armature or stator. It is very important to count the number of winds in every coil because it will have to be rewound in exactly the same manner for the device to work.
The insulation lining the stator should be inspected very carefully. Damaged insulation should be replaced with insulation tape or an the same material that was previously used. Hereafter the armature or stator can be rewound. It is vital to recreate the exact same winding patterns and the exact same number of coils as the original. Also, the same type of magnet wire and of the same gauge should be used.
The end of the first winding should be left apart and it must be long enough to reach the first of the tabs. The final winding will also be connected at that specific point. The wire can be held in place with a crimping tool. Care should be taken, however, to make sure that the wire makes decent contact with the tab. If necessary, some of the insulating material can be taken out.
Next, the end of the last winding and the loose wire from the first winding can be connected. After making sure that no wire connected to the tabs are touching. Thereafter it is simply a matter of assembling the housing again and to test the device. If it is not performing as expected it is best to ask a professional to examine the work done.
It is important to remember that electrical devices can be dangerous. Great caution should be exercised at all time, especially when testing the device. Children should not be allowed to become involved in such projects. In fact, they should not be allowed near the working area.
It is important to note that his type of project requires a high level of concentration and meticulous attention to detail. The device will not work if even small mistakes are made or if the rewind job was done poorly. If there are the slightest doubt it may be better to have the task performed by professionals. There is such a large variety of devices on the market that care should be taken when following on line instructions.
First, it is necessary to remove the housing in order to expose the armature, stator and windings. Experienced professional advise that detailed photographs be taken at this stage. When winding, the exact patterns and connections will have to be recreated and the photographs can be a big help in this regard. Even small mistakes can render the project a failure.
The next step is to take the wire from the brush pads, taking care not to disturb the tabs more than strictly necessary. The wire must be completely removed. Thereafter the coils can be cut in order to free them from the armature or stator. It is very important to count the number of winds in every coil because it will have to be rewound in exactly the same manner for the device to work.
The insulation lining the stator should be inspected very carefully. Damaged insulation should be replaced with insulation tape or an the same material that was previously used. Hereafter the armature or stator can be rewound. It is vital to recreate the exact same winding patterns and the exact same number of coils as the original. Also, the same type of magnet wire and of the same gauge should be used.
The end of the first winding should be left apart and it must be long enough to reach the first of the tabs. The final winding will also be connected at that specific point. The wire can be held in place with a crimping tool. Care should be taken, however, to make sure that the wire makes decent contact with the tab. If necessary, some of the insulating material can be taken out.
Next, the end of the last winding and the loose wire from the first winding can be connected. After making sure that no wire connected to the tabs are touching. Thereafter it is simply a matter of assembling the housing again and to test the device. If it is not performing as expected it is best to ask a professional to examine the work done.
It is important to remember that electrical devices can be dangerous. Great caution should be exercised at all time, especially when testing the device. Children should not be allowed to become involved in such projects. In fact, they should not be allowed near the working area.
About the Author:
Know whom to contact to repair your air conditioner motor pump Phoenix area by visiting the recommended source. A credible list of service providers will be found online when you log in at http://runemagainmotors.com/glendale-air-conditioner-motor-repair.php.
No comments:
Post a Comment